Bicycle Wheel Building: How a Custom Wheel Is Made

A wheel looks simple. A rim, a hub and a bunch of spokes. But some intricate details and the little things decide whether it rides well for years or goes wobbly in a month. Here's how bicycle wheel building works, start to finish, in plain words. Maybe you're just curious. Maybe you're thinking about lacing your own. Or maybe you want to know what to ask a wheel builder for.

What's in a wheel

Four parts do all the work.

  • The rim holds your tire. Its width, depth, material (alloy or carbon) and drilling decide which tires fit and how stiff the wheel feels.
  • The hub sits in the middle. Its axle standard, brake mount (6-bolt or Centerlock) and freehub body have to match your frame, brakes and cassette.
  • The spokes connect hub to rim. They come in different types, like J-bend and straight pull, and in different lengths.
  • The nipples are the small nuts at the rim end of each spoke. A builder turns them to set tension.

Everything has to agree. A rim drilled for 28 spokes needs a 28-hole hub, and a straight-pull hub needs straight-pull spokes. That's why a good build starts with the combination, not with one part picked on its own.

Before you lace anything, check that the rim and hub have the same spoke count. When we were learning, it was easy to get most of the way through the first round of spokes and find a few left over with nowhere to go.

Getting the spoke length right

If we had to pick the one number that matters most, it's spoke length. It gets calculated, not guessed. Too long and a spoke can poke through the rim. Too short and it won't hold the nipple properly.

A handful of measurements go into it:

  • Effective rim diameter (ERD): the diameter of the rim measured at the spot where the spoke ends sit. It's the number that matters most, and a small mistake in ERD changes the spoke length by roughly half as much.
  • Hub flange diameter and spacing: how far the spoke holes sit from the axle, and how far each flange is from the middle of the hub. Most hubs aren't symmetrical, so the left and right spokes often need different lengths.
  • Spoke count and cross pattern: how many spokes there are, and how many other spokes each one crosses.
  • Spoke hole and nipple details: the hole size and how deep the nipple sits.

You can try the numbers yourself with our free spoke length calculator. It asks for the rim and hub details above and shows the length for each side of the wheel. Check library data against the maker's numbers before you order spokes.

Lacing and spoke count

Lacing is just how the spokes are woven between hub and rim.

Lacing is our favorite part of building a wheel. You watch the hub settle in as the spokes start to pull it toward the center, the crosses take shape, and the wheel starts to come to life before you've even begun to tension it.

  • Radial: the spokes run straight out from the hub. It's simple and light, but it's often limited to certain hubs and often isn't the best choice for carrying drive or brake torque.
  • Two-cross and three-cross: each spoke crosses two or three others on its way to the rim. That extra crossing helps carry drive and braking forces, and it's a common choice for strong wheels.

Spoke count matters too. Fewer spokes (24) save weight and can suit lighter riders on smoother ground. 28 is a middle ground. 32 is the sturdy choice for heavier riders and rough riding. Our guide to choosing a spoke count goes through the trade-offs.

Tensioning, truing and dishing

Once the spokes are laced, the wheel is a loose, wobbly ring. These steps turn it into a wheel.

  1. Tensioning: you bring every spoke up to tension a little at a time, working around the wheel so the rim stays round. The goal is even tension. Too little and spokes loosen. Too much and you can damage the rim. The rim maker's tension limit comes first.
  2. Truing: the wheel spins in a truing stand, and you turn nipples until the rim runs straight side to side and round up and down.
  3. Dishing: the rim has to sit centered between the frame mounting points. On many rear wheels and some disc front wheels, the hub flanges aren't symmetrical, so the spokes on one side end up tighter than the other. That's normal. Dishing is how you handle it.
  4. Stress relieving: you press and release the spokes so everything settles, then check tension and trueness again. A wheel that hasn't settled can go out of true in its first rides. We prestress every wheel we build.

A tension meter, a truing stand, a dishing gauge and a spoke wrench are the tools you'll want. A good builder also leans on feel, and that comes from building a lot of wheels. It's hard to get from a book.

Mountain, gravel and road wheels

The steps are the same. The choices change.

  • Mountain wheels take hits from rocks and drops. Many use wider rims, a higher spoke count like 28 or 32, and strong hubs, and often a disc brake mount, either 6-bolt or Centerlock.
  • Gravel wheels sit in the middle: wide enough for bigger tires, strong enough for rough roads, and often lighter than a mountain wheel.
  • Road wheels go for low weight and, for some riders, aerodynamics, so many use lower spoke counts.

Wheel size, axle standard and freehub body also differ from bike to bike, so check your frame and cassette before you pick parts.

Build it yourself or have it built

Building your own wheel is rewarding. With patience, good measurements and a few tools, you can build a basic wheel. But the risks are real. A wrong spoke length, uneven tension or a wheel that hasn't settled can let you down on the trail. The most common problem we see on home builds is uneven spoke tension. A wheel can spin true and have the right dish and still hide a few spokes that are much looser than the rest. A loose spoke goes slack as the wheel turns under load, so it can work loose over time, and the spokes next to it have to carry the extra stress.

Having a builder do it gets you a wheel that someone has measured, tensioned and checked, and a person to ask when a question comes up. If you like to learn, there's a middle road: have a builder make your first set, then study it and try your own rebuild later. Either way, there's nothing wrong with doing it yourself. Just measure carefully and check your work.

How our Custom Wheel Builder works

If you'd like custom wheels without hunting down every part yourself, our Custom Wheel Builder walks you through three steps.

  1. Choose your ride: pick your riding style (Gravel / Road, Mountain or Hybrid), a wheelset or a single front or rear wheel, and the spoke interface (Standard or I9 System). You can also tick the box for a rim or hub you'll send us.
  2. Dial in your specs: set the wheel size, spoke count, hub spacing, brake style and freehub type.
  3. Choose your components: pick the rim, hub, spokes and nipples for each wheel, with an optional valve stem. A curated-build tool can suggest matching parts by material, rim depth and goal. A running total shows as you go.

Open the Spoke Color Studio to pick your spoke colors before you add the wheels to your cart. If you'd rather send a rim or hub you already own, tick that box in Step 1 and we build the wheel around it. Parts you send get inspected when they arrive. We work out spoke lengths for your exact rim and hub and build each wheel by hand, to order. Want to browse parts first? Start with our DT Swiss hubs, Industry Nine hubs, carbon rims and alloy rims.

Our warranty page explains what's covered once your wheel is built.

Common questions about bicycle wheel building

What is ERD and why does it matter?
Effective rim diameter is the diameter of the rim at the spoke ends. It's the key number for spoke length, so measure it carefully or take it from a source you trust.

Does spoke count change spoke length?
Yes. Spoke count and cross pattern change the angle of each spoke, and that changes its length.

What is dish?
Dish is how far the rim sits off the middle of the hub flanges. It lets the rim sit centered in the frame even when the flanges aren't symmetrical.

What tools does a wheel builder use?
A truing stand, a spoke wrench, a tension meter and a dishing gauge are the main ones, plus a good spoke length calculator.

Do front and rear wheels differ?
Often, yes. The rear has a cassette on one side and often needs more dish, so left and right spoke tension differ more than on the front.

Can I send my own rim or hub?
Yes, in our builder. Rims should arrive new or in excellent, undamaged condition, and hubs need the correct end caps and a complete freehub body. We inspect the parts when they arrive.

Still have questions about bicycle wheel building or ordering? Our FAQ covers custom builds, parts you send and the warranty.